Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio setup: mic gain, ALC, compression and bandwidth for clean signals that still work weak stations and DX

ci_cover.jpg

This thread is for sorting out SSB transmit audio setup. It is a common source of confusion, because a few knobs interact: mic gain, speech processor, equalizer, ALC and the transmit filter width. The starting point below should be checked against your own radio's manual, since meters and menu ranges differ between models.

Start with sideband and filters. By long-standing convention, amateurs use LSB on 160, 80 and 40 meters and USB on 20 meters and above. 60 meters is generally USB. The reason is practical: if everyone follows the convention, you can tune across a band without hunting for the right mode. Most receive-side problems come from filter width. A 2.4 kHz filter is a good general-purpose choice because it keeps speech readable without letting in much adjacent noise. In heavy QRM, a narrower filter around 1.8 to 2.1 kHz can help, at the cost of some tone quality. On a quiet band with a strong signal you can open it to 2.7 kHz or more. Narrowing the filter is a receiving tool and does not change what you transmit.

For the transmit side, begin with the microphone itself and your distance from it. Most of what people call bad audio is a mic placed too close, which brings in proximity-effect bass, plosives and breath noise. A distance of roughly one to two fingers' width, with the mic slightly off-axis from your mouth, is a reasonable starting point. A foam windscreen or pop filter costs little and helps. Check that your radio's mic settings match the type: dynamic and electret microphones need different bias settings, and the wrong one gives either no output or a distorted mess. Room reflections matter too, because a hard-walled shack will add a hollow sound that no processor will remove.

Set mic gain with the processor off first. Speak at your normal operating level, with the same energy you would use to be heard across a room, and adjust mic gain so the ALC meter just flickers on your loudest syllables. ALC stands for automatic level control, and it is a protection circuit rather than a modulation meter. If the ALC is pinned during normal speech, the audio chain is being overdriven, which produces flat-topping, distortion and splatter that spreads beyond your intended bandwidth. A sensible target is little or no ALC movement on peaks. With an external amplifier, also watch the amp's own ALC and drive limits, because overdriving the exciter will make the amplifier's output broader than your radio alone.

The speech processor, or compressor, reduces the dynamic range of your voice so average power increases relative to peak power. On SSB, output is rated in peak envelope power, but speech has a low average-to-peak ratio, so a modest amount of compression can improve readability when the signal is marginal. The gain is often a few dB, which is not much, but it can be the difference between copyable and not. The risk is overdoing it. Heavy compression raises background noise and makes sibilants harsh. It also magnifies room echo, and a processor set too hard produces distortion products that can be heard on adjacent frequencies. Many radios show compression level on a meter during transmit. A few dB is typically reasonable, and pushing toward 10 dB or more usually sounds worse to the listener. Remember also that some radios apply compression at audio frequency and some at RF or IF, and these behave differently, so read what your model does.

The monitor function lets you hear your own transmit audio in headphones. It is useful for judging how processing and EQ sound, though not a perfect picture of what the other station hears, since it comes from your own radio's audio path and not through propagation, their filters and their noise. Keep the monitor level modest in headphones to avoid feedback, and avoid speakers on while transmitting if the mic is nearby.

The equalizer is the next step, after the gain structure is right. The usual approach is to reduce low frequencies below roughly 150 to 200 Hz, since this energy uses power without adding intelligibility, and to give a gentle lift in the 2 to 3 kHz region where consonants live. Large boosts tend to sound harsh. Radios with a transmit bandwidth setting let you choose, for example, 100 to 2900 Hz for a fuller sound or a narrower window for DX. A wider transmit signal can sound nicer on a strong, quiet path, but when you are calling a weak station or running in a pileup, a narrower, punchier signal concentrates energy where the receiver's filter is listening.

For weak stations and DX, technique matters about as much as hardware. Speak at a steady pace, give the callsign clearly with standard phonetics, and repeat it rather than relying on one pass. Avoid shouting, which tends to overdrive the audio chain and does not add useful power. If your readable signal depends on the radio's processor to be heard, the answer is usually better placement of the filter edges and a cleaner receive setup. On receive, try the narrow filter, reduce AGC problems, and use noise reduction sparingly, because aggressive noise reduction can make speech sound watery and hide weak syllables.

Finally, test rather than assume. Ask a local operator for a report with processor on and off. If a web SDR near you covers the band, listen to your own signal there. Record a short transmission into a dummy load or a second receiver, and compare settings one change at a time. What does your setup look like, and which control changed your audio the most?

  • Replies 2
  • Views 11
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One point worth adding is that ALC behavior is not the same on every radio, so reading the meter requires knowing what it measures. On some rigs the ALC meter shows only the ALC voltage, and it will stay near zero until you exceed the threshold, so the right setting is to peak just at the start of movement. On others the meter scale has a marked zone, and the manual says to stay inside it. Check the manual before adopting a general rule. And if the radio has a separate compression meter, use it, because ALC and compression readings tell you different things.

On equalizer settings, many operators cut the bass first and only then think about adding highs. The reason is that low frequencies take up a lot of the available power but contribute little to readability. If the voice sounds thin after that, try reducing the cut rather than boosting the highs. A little at a time is better than a dramatic curve.

  • Moderators

On the DX side, I would stress that the best audio is not the same as the loudest. In a pileup the station you are calling is using a narrow receive filter, often not far from 2.4 kHz or less, and may be listening through QRN and fading. The signal that gets through is usually the one with clean, consistent modulation and a clear callsign, not the one with the heaviest processing. Overprocessed audio can also hurt copy when the band is noisy, because the compressor lifts the noise between words and makes the speech harder to follow.

Another practical point is split operation. When the DX is listening up, make sure you have actually set your transmit frequency correctly and are not drifting while you adjust gain. Also keep an eye on your own splatter, since a signal that is slightly overdriven in a pileup will annoy nearby stations as well as hurting your own chances. If you can, ask someone a few kilohertz away how you sound. A quick report on whether you are splattering tells you more than another change at the EQ.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.