Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a wire antenna from scratch: wire, insulators, chokes, and checking it with a VNA and a model

ci_cover.jpg

This thread is for sorting out the decisions in a homebrew wire antenna. A 40 m dipole is a good example, but most of this applies to inverted-Vs, fan dipoles, end-feds and simple verticals. Parts lists get shared a lot, but the reasoning behind each choice gets less attention. Here is a rough order of operations. Please correct or add to it.

Wire. For a permanent span, 14 AWG hard-drawn copper or copper-clad steel is common. Soft-drawn copper stretches over time, so the resonant frequency drifts and the sag changes. Copper-clad steel resists stretching but is stiffer and harder to coil. For portable or lightweight antennas, 18 to 22 AWG stranded wire is fine. Thinner wire only costs you a little in resistive loss at HF, but it has less tensile strength and a slightly narrower bandwidth. Insulated wire has a velocity factor effect, so it resonates lower than bare wire of the same length. The shift is often a few percent, which is why the standard advice is to cut long and trim.

Starting length. The familiar 468/f(MHz) feet formula gives total dipole length. For 7.1 MHz that is about 65.9 ft, or roughly 33 ft per leg. Height above ground, nearby objects, wire type and sag all move the resonance. Treat the formula as a starting point and plan on adjustment. Fold the extra length back on itself at the end insulators instead of cutting it off, so you can still change it.

Insulators and supports. The center insulator carries the mechanical load of the feedline. Give the coax or ladder line some strain relief so the pull does not land on the solder joint or the wire itself. End insulators can be anything non-conductive and UV-stable: ceramic, HDPE, acrylic, or even sections of PVC. Weather and sunlight are the real enemies. Use rope that tolerates UV and does not stretch much. Where a tree can move, add a pulley and counterweight or a bungee section so the wire does not break in the wind. For fiberglass poles, check what the wire does at the joints. Tape or clamp the wire at intervals instead of letting it flap, and keep poles well away from power lines.

Feedline choices. A half-wave dipole fed with 50 ohm coax and a 1:1 current balun or choke is the simplest single-band setup. A multiband dipole is more flexible fed with 450 ohm window line or ladder line into a tuner. With ladder line the feedline is part of the system, so keep it balanced, away from metal, and avoid running it parallel to other conductors. On the coax side, a choke of coiled coax or a stack of type 31 or 43 ferrite is common. The goal is high common-mode impedance, ideally a few thousand ohms, on the bands you use. A choke is not an impedance transformer. It only suppresses current on the outside of the coax shield.

Traps versus fan dipoles. A trap is a parallel LC circuit resonant at the band you want to isolate. Traps work, but they add loss and narrow the bandwidth, and they need to be weatherproofed and tuned individually. Fan dipoles use several wires from one feedpoint and are easier to build and adjust, but the elements interact. In practice you trim the highest band first, then work down.

Verticals and radials. A quarter-wave vertical for 40 m is about 33 ft tall, using 234/f(MHz) as a starting figure. The radial system decides how much power goes into the air and how much into the soil. Elevated resonant radials, a few of them, are efficient. Ground-mounted verticals often need many radials, commonly 16 or more, to bring ground loss down. A low SWR on a vertical with a poor radial field can still be a lossy antenna, so SWR alone is a weak test of efficiency.

Measuring. An antenna analyzer or NanoVNA is more informative than a basic SWR bridge because it shows resistance and reactance as well as SWR. Calibrate at the point where you connect. Keep in mind that common-mode current on the shield can shift readings, and that lossy coax makes the SWR at the radio look better than at the antenna. Measure with the choke installed, and compare results at the antenna end and the shack end.

Modeling. Both EZNEC and MMANA-GAL let you check a design before cutting wire. Use sensible segment counts, a realistic ground type and the actual wire diameter. Expect the model to match reality only as far as the inputs do. Neither program accounts for common-mode current unless you add the feedline as part of the model. Even so, models are good for comparing options such as height, fan spacing, sloper angle or radial count.

Questions for the thread: what is your usual workflow for trimming and verifying a new antenna? Do you model first, or build and measure? And where do you draw the line between a trap design and a simpler fan?

  • Replies 2
  • Views 10
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One suggestion on workflow: model first only to pick a target length and see how sensitive the design is to height, then build with extra wire at the ends. A model will tell you things like "the resonance moves by X kHz per foot of height change," which helps you decide how much trimming margin to leave. It will not tell you your actual resonance, because soil, nearby metal and sag are not in it.

For checking the final result, I would keep two measurements separate. Measure resonance and impedance with a VNA at the antenna feedpoint, ideally with a short jumper. Then measure again at the end of the actual feedline in the shack. If the two differ much, you are seeing feedline loss or common-mode current. That difference is itself a useful diagnostic. A good test is to touch or move the coax and see whether the reading changes. If it does, the choke is not doing enough.

On traps versus fans: if you only need two or three bands and have space for the extra wires, a fan is usually less work. Traps make more sense when you have a fixed length limit and cannot spread the wires out.

  • Moderators

On the vertical side, I would underline that "SWR looks fine" and "it works well" are different statements. A quarter-wave vertical over a thin radial field can have a feedpoint resistance that looks like a decent match, but part of that resistance is ground loss. If you can only run a few radials, raising them off the ground and cutting them near resonance usually does better than laying a handful on the surface. A common elevated arrangement has the radials drooping at an angle, which also brings the feedpoint resistance closer to 50 ohms.

For modeling in EZNEC or MMANA, check the ground setting for verticals especially, since results depend heavily on it. Compare the model with a perfect-ground run and with an average real-ground run. The difference gives you a feel for how much a poor ground costs, even though the numbers will not be exact for your site.

Also, a quick note on fiberglass poles: the weight of a long wire, plus a pole that is only secured at the base, can bend it badly in wind. Guying at one or two points is worth the trouble, and keep guy lines non-conductive or break them up with insulators so they do not interact with the antenna.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.