Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Sequencing a homebrew QRP station: receiver first, then transmitter, then the test gear that keeps you honest

ci_cover.jpg

A lot of people start homebrew with a transmitter because it feels like the exciting part. But the order you build things in has a big effect on how much you learn and how many dead ends you hit. This thread is for comparing build orders and for talking about what is actually worth building, buying or skipping.

Here is one possible sequence to argue with. Start with a receiver, since a receiver that works is the best test instrument you will own. A direct-conversion receiver for 40 m or 80 m is a good candidate: a bandpass filter, a diode-ring or active mixer, a VFO or crystal-controlled local oscillator, and a high-gain low-noise audio chain with an LM386 or an op-amp stage at the end. Its flaws teach a lot. You get both sidebands at once (no sideband rejection), AM broadcast breakthrough if the front end is too wide, hum and microphonics if the audio stage is badly laid out, and local oscillator leakage back to the antenna if there is no isolation.

Next comes a small crystal-controlled CW transmitter. The Tuna Tin 2, a 1970s QST design for 40 m, is a good template: one crystal oscillator stage running at a few hundred milliwatts, followed by a low-pass filter. The point is to learn what a clean key-down signal looks like and why a Pi-network or low-pass filter on the output is not optional. A Pixie-style transceiver is even simpler, but its receiver is very broad and the whole thing is closer to an educational toy than a station rig. Fun, but set your expectations accordingly.

After that, the choice is between building something like a BITX (a bidirectional SSB transceiver with a crystal ladder filter, a diode-ring mixer and shared amplifier stages) or buying a kit such as the uBITX, which is multiband and uses an Si5351 clock generator controlled by an Arduino Nano. The uBITX is a very capable platform for the price, but the build is the beginning rather than the end: people commonly check harmonic suppression, the output filters per band, and how much power the rig really makes on each band at their supply voltage.

Then there are accessories: an SWR bridge, a dummy load, a simple keyer, and a power supply that does not put noise into a sensitive direct-conversion front end. Which of these would you build first, and what would you skip altogether?

  • Replies 2
  • Views 12
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I would move a dummy load and an RF probe ahead of almost everything else. A 50-ohm load that can take your rig's full power for a minute or two lets you adjust and test a transmitter without sending a signal to the antenna. Several 1/2 W or 2 W metal-film resistors in parallel will do for the lowest-power transmitters. For anything over a couple of watts, use a proper load or a well-heat-sunk resistor array, and be aware that resistor inductance and stray capacitance make homemade loads less accurate as the frequency goes up.

On the receiver side, one detail often missed with direct-conversion designs is that the audio stage matters as much as the mixer. The mixer output is often only a few microvolts to millivolts, so you need on the order of 80 to 100 dB of gain with a low noise floor. Poor grounding, supply ripple and a long lead from the mixer to the first audio stage are the usual causes of hum and oscillation. A low-pass filter at the audio output (even a simple RC or a few-pole active filter around 2.5 to 3 kHz) makes a surprising difference to how a receiver feels to use.

For the SWR bridge, a tandem-match or Bruene-style bridge is simple, but calibrate it against known loads. With a 50-ohm dummy the reflected reading should null. A 100-ohm resistor should read about 2:1 SWR, and 150 ohms about 3:1. If it does not, then either your balance is off or the diodes are behaving differently at low power. QRP power levels mean the diode forward drop becomes a significant factor, so a bridge that reads fine at 10 W can look misleading at 1 W.

  • Moderators

For kit building, a few habits pay off more than a better iron. Sort and identify parts before starting, and check resistor values with a meter rather than trusting color bands in poor light. Fit low-profile parts first, then taller ones. Test in stages: confirm the power rail and current draw before populating the rest of a board. A current-limited bench supply or even a series resistor or fuse in the supply lead can save a board from an accidental short or reversed polarity.

Toroids are where many builds go wrong. Turn counting is by the number of times the wire passes through the center hole, not by the number of loops on the outside. Enamel wire needs to be properly stripped and tinned before it is soldered. Check the core material as well: a T37-2 (red) and a T37-6 (yellow) have different permeability, so the same number of turns gives a different inductance. If you have a NanoVNA or an LC meter, check the finished inductor values and sweep the low-pass or bandpass filters rather than assuming the design numbers worked out.

On the uBITX in particular, I would treat the stock build as a starting point. The output on the higher bands should be checked for harmonics and spurs, ideally with a spectrum analyzer or at minimum a receiver tuned to the harmonic frequencies. Supply voltage and power headroom matter too, since the PA gets hot at a high duty cycle. Good practice is to use a power supply that can handle the peak current, add reverse-polarity protection, and keep any switching regulator well away from the receive path. A linear supply or a battery is a good reference when you suspect a noisy supply is raising your receiver noise floor.

As for what to skip: very simple one-transistor transceivers are fun to build and teach basic ideas, but they do not teach selectivity, AGC, or clean transmit practice. A receiver with a crystal filter and a transmitter with proper low-pass filtering teach more per hour of building.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.