Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24-hour EMCOMM field station: power budget, antenna and coax choices, grounding, and noise control

ci_cover.jpg

This is a planning thread for a generic 24-hour field deployment: one HF station, one VHF/UHF station, a laptop for logging and digital modes, and basic lighting, all under a pop-up canopy or small tent. The aim is a layout that survives real conditions, not just one that works in the driveway. Below is a proposed approach. Please poke holes in it.

Power budget first. Size the system on average current over time, not on the radio's peak transmit rating. An illustrative estimate: HF rig averaging about 4 A (mostly receive, with SSB or digital bursts), dual-band VHF/UHF rig about 2 A, laptop about 2.5 A (30 W), lighting and accessories about 1 A. That is roughly 9.5 A, or about 115 Ah over 12 hours. A single 100 Ah LiFePO4 battery is therefore not a 24-hour plan unless something charges it. Replace the numbers with your own measurements. A cheap inline DC meter or shunt-based monitor will tell you more than the spec sheet.

Charging options. An inverter generator can run efficiently as a battery charger instead of powering the station directly. Run it for a block of time with a suitable charger or DC-DC supply, then shut it off for quiet operation. Solar is quieter but weather-dependent. As a rough guide, a 200 W panel under good conditions delivers perhaps 60-70% of its rating at the battery, about 10 A at midday, and a day's harvest of maybe 40-55 Ah depending on location, season, and shading. Use an MPPT controller with a LiFePO4 charge profile. Check the battery's low-temperature charging limits, since many LiFePO4 batteries should not be charged below freezing unless they have built-in protection.

Distribution. Fuse close to the battery, then use a fused distribution block with Powerpole-style connectors. Pick one polarity orientation and enforce it across the whole group. Keep high-current runs short and heavy. For example, 10 AWG over a 10 ft run each way carries 20 A with about 0.4 V of drop, which is already noticeable on a 13.8 V rig. Know your battery's BMS behavior too. Some cut off abruptly at low voltage, which can drop the whole station mid-message. A voltage alarm or a monitor with a warning threshold is worth having.

Antennas and coax. For regional HF, a low dipole or inverted-V on a fiberglass mast is a solid baseline. At lower HF frequencies, NVIS-style low-angle-radiation setups can cover nearby areas when ground-wave and line-of-sight paths do not. For VHF/UHF, put the antenna as high and as clear of the shelter as practical, and treat coax loss as a real part of the link budget. As ballpark figures, RG-58 is on the order of 1 dB per 100 ft on 20 m but several dB per 100 ft at 2 m and worse on 70 cm. Lower-loss coax matters far more at VHF/UHF than at HF. Check the datasheet for the cable you actually carry.

Grounding and safety. A temporary ground rod does not make a field station lightning-safe. Treat thunderstorms as a stop-operating event: disconnect coax, lower antennas if it can be done safely, and stay away from masts. Keep masts and wire antennas well clear of power lines, with a distance that accounts for the mast falling, not just standing. Guy every mast, anchor stakes properly, and watch wind loading on canopies as well.

Noise. The usual sources are the generator, switching power supplies and chargers, laptop and USB hardware, and LED lighting. Common-mode current on coax and power leads is often the path. Put a current choke at the antenna feedpoint and another near the radio, add ferrites on DC and USB leads where they help, and keep the generator downwind and well away from antennas. Never run a generator inside or near a tent opening, and use a CO alarm in occupied shelters regardless of generator placement.

Questions for the group: What belongs on a setup-and-teardown checklist beyond the obvious? How do you decide when to stop adding gear and keep the deployment simple? And what is the first thing you would drop if volunteers and time are limited?

  • Replies 2
  • Views 10
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Good starting point. I'd split the power plan into three layers. First, a critical-load bus: the primary radios, a handheld charging path, and one light. Second, a convenience bus: laptop, chargers, extra lighting. Third, generator or mains-powered loads such as a heater or fan. When the battery gets low, you shed from the bottom up and the net still works.

On the generator-as-charger idea, I'd add that inverter generators are most efficient at moderate load, so running one at a trickle load all night wastes fuel. A better pattern is to charge hard for a defined window, then shut down. Keep fuel storage, refueling, and placement as part of the checklist, including letting the unit cool before refueling and keeping exhaust away from tents. Follow the manufacturer's instructions on neutral-ground bonding, and don't improvise backfeed connections. If you power anything from an AC outlet, GFCI protection is a sensible baseline outdoors.

On LiFePO4: the flat voltage curve is nice for rigs but makes voltage a poor fuel gauge. A battery monitor that counts amp-hours or tracks state of charge is much more useful than watching a voltmeter, and it makes the 'when do we start the generator' decision objective.

  • Moderators

I'd stress-test the antenna side with a few practical questions. How fast can two people raise the mast and have it guyed correctly? A dipole that takes 40 minutes to deploy is not an EMCOMM antenna. Carrying a quick-deploy backup, such as a simple vertical or an end-fed wire in a tree, is worth the weight. If you use an end-fed half-wave, remember it depends on a counterpoise and is prone to common-mode current, so a choke at the rig end is not optional.

For coax, label both ends with length and type, and keep a short list of known-good jumpers and adapters. A lot of field problems are connector problems: PL-259 half-seated on a barrel, a weather-damaged jumper, or a coax that was fine until it got stepped on. A cheap antenna analyzer or SWR meter belongs in the kit. It tells you whether the problem is the antenna system before you start blaming the radio.

For the shelter, put the radios where you can reach the key connections with the tent door closed, and keep a drip loop on every cable entering. Put gear on a tarp or table rather than directly on the ground, and tie down anything that could catch wind. For the checklists, I'd write the setup order as: site survey and hazards, power, antenna, radio check on the planned frequencies, and only then logging and message handling. Teardown is mostly the reverse, plus a headcount of stakes, connectors, and adapters, and a note on battery state and anything damaged for the next deployment.

Last point: the served agency or net control may care more about your communications plan than your hardware. Know frequencies, check-in procedures, message formats, and backup channels before you go.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.