Building a light POTA/SOTA go-kit: EFHW vs. linked dipole, pole choices, LiFePO4 sizing, and what to do about logging
- Replies 2
- Views 11
- Created
- Last Reply
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
I'd like to get a discussion going on how people put together a go-kit that works for both park activations and summit trips, without the pack turning into a second job. Weight and setup time matter on a hill. In a drive-up park you can afford a bigger battery and a chair. A kit that covers both is worth thinking through.
Antenna first. The two usual candidates are an end-fed half-wave (EFHW) with a 49:1 or 64:1 matching transformer and a linked dipole. The EFHW is popular because it's a single wire. A 40 m version (roughly 20 m / 66 ft of radiator) also works on 20, 15 and 10 m, since those bands are harmonics. You can run it as an inverted-L, a sloper, or an inverted-V with the feedpoint near the ground, so you only need one support. The catches are the feedpoint's sensitivity to the counterpoise (a short wire or the coax shield becomes part of the antenna) and common-mode current on the coax. A choke at the radio end is cheap and often makes the difference between a quiet receiver and a noisy one.
A linked dipole is center-fed and balanced, with links, usually small connectors or clips, to switch between bands by shortening or lengthening each leg. It's very efficient and needs no tuner, but you need a support tall enough for the center, and you have to walk out and change links when you change bands. If you mostly work one or two bands per outing, that's fine. If you like band-hopping to chase spots, it gets old.
Then the pole. Many people use a 10 m (33 ft) fiberglass telescopic pole, which is a good match for a 40/20 inverted-V or an EFHW sloper. The failure points are the thin top sections and the collapsing sections that slip under load. Hose clamps or a bit of tape at section joints help, and so do a couple of light guy lines at the top third. Wind is what breaks these poles, not the weight of the wire. Staking or tying the base to something solid is worth the extra two minutes.
Power: LiFePO4 is the usual choice now because the voltage stays flat and the weight is reasonable. A 4-cell pack is about 12.8 V nominal, around 14.4 to 14.6 V fully charged, so check that your radio is happy with that top end (most 13.8 V rigs tolerate it, but check the manual). A small QRP rig can run a long time from a few amp-hours. A 100 W rig on SSB or FT8 needs more, and FT8 duty cycle will drain a pack faster than casual SSB. Put a fuse close to the battery, use Powerpoles or something equally unambiguous for polarity, and remember that most LiFePO4 packs shouldn't be charged below freezing unless they say they're rated for it. If you add a solar panel, use a controller with a LiFePO4 charge profile rather than a basic lead-acid one.
Logging is where a lot of activations get messy. Paper in pencil is still the most reliable thing when it's wet, cold, or your phone is at 5%. For POTA you need 10 contacts in a UTC day for a valid activation, and for SOTA you need four contacts for points, so keep an eye on the UTC date if you operate across midnight. Whatever you use, it should export ADIF without much cleanup.
Last thing: weather and safety. If thunderstorms are forecast, a pole and wire is a lightning rod, so pack up early and leave the summit. Tell someone your plan and your expected return time. Carry water, a layer you don't need until you do, and a way to get weather updates.
So what's in your kit, and what did you drop because it wasn't worth carrying? And which would you pick for a first build: EFHW or linked dipole?
Link to comment
https://www.hamradiobase.com/forums/topic/11808-building-a-light-potasota-go-kit-efhw-vs-linked-dipole-pole-choices-lifepo4-sizing-and-what-to-do-about-logging/Share on other sites