Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio chain: mic gain, ALC, compression and bandwidth for a clean signal that carries in DX conditions

ci_cover.jpg

Many SSB signals that sound "loud" on the band are hard to copy, while a clean signal at the same strength is easy. Here is a starting framework for the audio chain, and I'd like to hear where people disagree with it.

1. Start with the microphone and the room. No setting fixes a bad source. Keep the mic roughly a hand-width (a few centimetres) from your mouth, slightly off-axis, so plosives and breath noise don't hit the capsule. A foam or mesh pop filter helps. Fans, computer noise and room echo go straight into the compressor and come out louder. A dynamic mic with a limited, speech-oriented response often does better on the air than a wide-range studio condenser, which picks up more room and gets less benefit from a 2.4 kHz passband.

2. Set mic gain by watching ALC. With the processor off, speak at your normal DX volume and adjust mic gain until the ALC meter only touches its allowed zone on voice peaks. Constant ALC action means the rig is flattening your peaks, which adds distortion and splatter. Meter behaviour varies between radios, so check your manual for the intended ALC range. Also check the power output: the ALC is protecting the final stage, not telling you how good the audio sounds.

3. Add compression only after the clean setup works. A speech processor raises average power relative to peak power, which is the point of it in weak-signal work. Mild settings can add a few dB of readability. Heavy settings raise the background noise, emphasise sibilance, and can produce a harsh, distorted sound that is harder to copy than a modest-level signal with clean dynamics. A useful approach is to bring the compression level up gradually while listening to a recording or asking someone for a report, and stop as soon as it stops sounding natural. Be aware of the difference between AF compression and RF clipping, since they behave differently and not every rig offers both.

4. Use the monitor, but know its limits. The TX monitor lets you hear your processing and spot hum, hiss or heavy compression. It does not reproduce exactly what the far end hears, particularly if you use a speaker rather than headphones, which can cause feedback. Use headphones and set the level low. The best check is a recording from an SDR or a second receiver, or a report from someone who is able to describe the sound in detail.

5. Equalizer: small moves. Roll off the lows below about 150 to 200 Hz, because they use transmitter power without adding intelligibility. A mild lift in the presence region around 2 to 3 kHz can help consonants. Avoid large boosts, since they can make the compressor push sibilants and increase distortion. If your rig has TX bandwidth or a low-cut and high-cut control, adjust them in coordination with the equalizer rather than separately.

6. Transmit bandwidth. Around 2.4 kHz is a common default for efficient communication, and many rigs allow roughly 2.7 to 3.0 kHz or more. A wider setting sounds fuller on a quiet band, but it uses more spectrum and can bother neighbours on a busy one. In DX conditions and contests, many operators keep it close to 2.4 kHz, or narrower, so the power sits in the part of the audio that carries intelligibility.

7. Upper and lower sideband. By convention, LSB is used below 10 MHz (160, 80 and 40 m) and USB above it (20 m through the higher bands). 60 m channelised operation is USB, and 30 m is mostly digital and CW. If you are unsure, listen to others on that frequency, and follow your national band plan.

8. Receive side for weak stations. A 2.4 kHz filter is a general starting point. When there is adjacent QRM, narrow the passband to somewhere near 1.8 to 2.1 kHz, or use passband shift or IF shift to move away from the interference. Be careful with the AGC and preamp: a preamp is useful on higher bands where the noise floor is low, but it can add overload on lower bands at night. Reduce RF gain or use the attenuator if strong signals are producing audible distortion. Noise reduction can help at a modest setting, but heavy use makes speech sound watery and can mask the weakest syllables.

9. Working DX efficiently. Listen for the station's pattern before calling, find out whether they are working split, and keep your call brief. Keeping the transmission short and using standard phonetics usually gets a better result than more power with poor audio. Check that your amplifier, if you use one, is not being overdriven, because a clipped or flat-topped signal is wider than it should be.

What order do you use when setting up the chain, and have you found that a compression setting that looks fine on the meter sounds worse on the air?

  • Replies 2
  • Views 9
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One useful change is to treat ALC as a limit rather than a target. If it only moves on the loudest syllables, the rig is probably operating linearly. If it moves on every word, mic gain or the processor drive is usually too high.

On compression, a number on a dial doesn't tell you much, because rigs scale it differently. A better test is to make a recording with the processor off and again with each setting, then listen at low volume through a small speaker. The best choice is the one where the words are easier to follow, not necessarily the one with the biggest level change. Increased background noise between words is a sign it has gone too far.

  • Moderators

I'd add that the best audio depends on what you're trying to do. For a casual chat on a quiet band, a wider and fuller transmit response sounds nice and is good practice. For a pileup on a DX station, the aim is just to be understood the first time, so a narrower, more punchy and well-controlled signal is better.

For the receive side, it helps to keep the filter wide enough while searching and then narrow it once you are on a station. It's easy to leave a narrow filter on and miss callers who are slightly off frequency. Also check your AGC speed: a slow AGC with a loud nearby signal can cover the weak station you wanted, while a fast one can make the background noise pump up between words.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.