Everything posted by Mod_Chad
-
Small-yard HF antennas: comparing EFHW, OCFD, doublet, vertical and loop by what the SWR meter can't tell you
The radial question deserves some numbers. A quarter-wave vertical over an ideal ground has a feedpoint around 36 ohms, so a low SWR into 50 ohms can mean either a good match or a lot of ground loss added to the radiation resistance. That's a classic trap: the SWR looks better as the ground gets worse. For a ground-mounted vertical, it's common to recommend 16 or more radials, and more is better. For an elevated vertical, two to four tuned radials per band can work well, and sloping them downward raises the feedpoint toward 50 ohms. Modeling software such as 4nec2 or EZNEC can help you compare a 35 ft inverted V, a vertical and a loop over your own ground assumptions before cutting wire. Treat the results as relative comparisons, because real soil and nearby wiring change things. For stealth, thin dark wire is much harder to notice than people expect, especially against trees. A multiband doublet strung between a tree and the house eave may attract less attention than a vertical on a pole. For covenant reasons, a loop in the attic is a fair last resort. Attic wiring, ducting and roofing metal will detune and absorb, though, so expect a compromise and keep RF exposure limits in mind when the antenna is close to living space.
-
Dual-band mobile rigs (FTM-500D, ID-5100A, TM-D710G): what matters in the install, and what to check before relying on cross-band repeat
On the choice between the three, I would start with the local network rather than the spec sheet. If the repeaters you use are D-STAR, the ID-5100A makes sense. If they are Fusion or WIRES-X-linked, the FTM-500D is the natural fit. If your area leans on APRS for tracking and messaging, the TM-D710G's built-in TNC is a real advantage because it needs no outboard hardware. A digital-voice radio that nobody around you uses is just a 50-watt FM radio with extra menus. On wiring, the thing worth repeating is that the fuse protects the cable, not the radio. If the positive lead shorts to the body a foot from the battery, the fuse has to be at the battery end to do anything. Also check that the negative connection is on a clean, bare metal point or the battery negative. A painted or corroded ground point can cause intermittent resets and odd noise that is easy to mistake for a radio fault. For the cross-band section, I would make sure that anyone planning to use it reads the manual's section on it before assuming it works like a home repeater. Some radios want specific settings for offsets, tones and which band does the receiving, and the ID requirements still apply.
-
2026 CQ World-Wide DX Contest (CW)
until
The CW weekend of the CQ World-Wide DX Contest. Amateurs worldwide try to contact as many CQ zones and countries as possible. The contest runs from 00:00:00 UTC Saturday to 23:59:59 UTC Sunday. It uses six HF bands, 1.8 to 28 MHz. The CW exchange is an RST report plus the CQ Zone number. Logs must be submitted electronically by 2359 UTC on December 1, 2026.Location: Worldwide (on-air, HF amateur bands 1.8-28 MHz; no physical venue) Organizer: CQ World Wide DX Contest (CQ Magazine), cqww.com Source: Event information -
ARES, RACES, SKYWARN, CERT: how do you sort out where you fit, and what to train on first?
Start with your local group, not the acronyms. Before buying gear, find out who your Emergency Coordinator or RACES officer is, which agencies your county actually serves, and whether the group meets, holds regular nets or runs exercises. Plans differ a lot between counties and states. One place may have ham stations in the EOC, and another may mostly staff shelters and hospitals. Knowing that tells you which training matters most. For courses, FEMA's IS-100 and IS-700 are free and online, and they teach the vocabulary you will hear in an EOC or at an incident: span of control, unified command, resource requests, and plain language instead of 10-codes. Add a CERT class if one is offered nearby. Even if you never use the skills, it puts you in contact with the people you may work beside. SKYWARN is worth doing as well, and NWS offices generally offer free training sessions, though schedules vary. On the radio side, practice being a boring, reliable operator. Use tactical call signs where the plan calls for them, still ID with your FCC call sign as required, speak briefly, and write everything down. Message handling takes repetition. A radiogram has a number, precedence, station of origin, check count, place of origin, time and date, addressee, text and signature. It is easy to garble if you have only read about it. Nets, drills and the ARRL Simulated Emergency Test are good places to practice before it matters.
-
When Moving the Coax Changes Everything: Hunting Common-Mode Current
If your SWR shifts when someone walks past the feed line, your receive noise changes when you reroute a cable, or you get a tingle from the rig's metalwork on 40 meters, you probably have common-mode current. It is one of the most common hidden variables in amateur antenna systems, and it can make good antennas look bad and bad antennas look mysterious. What common-mode current actually is Current on a coax feed line should be equal and opposite on the center conductor and the inside of the shield. That is differential-mode current, and it stays inside the cable. If the antenna is unbalanced or poorly isolated, some current can flow on the outside of the shield instead. That is common-mode current. Once it is there, your feed line is part of the antenna. It radiates, picks up noise from household wiring, and brings RF back into the shack. Several setups invite it: A center-fed dipole fed directly with coax and no choke, especially where the coax drops away close to one leg. An off-center-fed or end-fed antenna with a small or missing counterpoise. The coax shield often becomes the counterpoise by default. A vertical with few or short radials, where the shield provides the return path the ground system should have. Any antenna near its own feed line, house wiring, or a metal mast, where coupling is easy. Symptoms worth taking seriously SWR depends on the coax. If the reading changes when you move the cable, coil it differently, or add a few feet of length, the shield is participating in the antenna. RF in the shack. Distorted audio, a hot microphone or keyer, computer interface dropouts, or a rig that behaves differently with power level can all point to RF returning on cables. Noise that tracks the feed line. If the receive noise floor changes when you shift the coax or add a choke, the cable is acting as a noise antenna. Pattern surprises. A dipole that seems to favor strange directions or lacks the expected nulls may have a radiating feed line. None of these proves common-mode current on its own, but together they are a strong hint. The good news is that the test is cheap and quick. A simple diagnostic sequence Change one thing at a time and write down what you see. Here is a sequence that works with a NanoVNA or an ordinary antenna analyzer. Baseline sweep. Measure SWR across the band of interest with the cable in its normal position. Save the trace or note the minimum SWR frequency, SWR at that point, and SWR at the band edges. Disturb the coax. Move the feed line, lay a section on the ground, or add a short extension. Sweep again. A large shift is a flag. A clean system will change much less, though some change from loss and mismatch is normal. Add a temporary choke. Clip clamp-on ferrites or coil the coax into a rough choke near the feedpoint. Sweep again and compare. Check receive noise. At a fixed frequency with the same receiver settings, compare the noise floor before and after. Use the S-meter or a software spectrum display, and try to compare under similar conditions, since band noise varies by time of day. Listen for RF in the shack. At modest power, see whether audio distortion, interface problems, or other symptoms improve. If the SWR curve becomes more stable and predictable and the noise drops, you have found something real. If nothing changes, the problem is likely elsewhere, such as a bad connector, a poor ground, a local noise source, or the antenna itself. Building a decent choke A common-mode choke is a high impedance placed in series with the shield's outside path. It does not affect the signal inside the coax. The goal is high impedance across the band, and the usual rule of thumb is several thousand ohms, with 5 kΩ or more often cited. The details depend on your antenna and noise environment. The two common approaches are: Ferrite beads or cores on the coax. Stack a number of cores over the cable, or wind turns through a toroid, using a mix suited to your bands. Mix 31 is often used for lower HF, and mix 43 tends to suit higher HF and VHF. Check the manufacturer's data for your frequencies, because not all ferrite is equal. Coiled coax. A choke made by winding coax into a coil is simple and robust, but its performance depends on coil size and the bands you use. It tends to work better on a limited range than across all of HF. Do not trust a choke because it looks professional. Measure it if you can. With a NanoVNA, you can use a series-through test fixture or a documented S21 method on the choke wound on a short sample of cable. Compare designs by their impedance on your bands, not by how many cores you used. Where to put it The most useful position is usually right at the feedpoint, where you want to stop current from getting onto the coax in the first place. A second choke where the cable enters the building can help if noise or RF is still coming in along the line. For end-fed antennas, treat the choke and counterpoise as one system. A choke can stop the shield from acting as the counterpoise, which means the antenna may then need a real counterpoise wire to work well. One more caution: chokes can heat up at high power if they are lossy or poorly matched to the band. Check the ratings and temperature on a test run before you leave a design in service at full power. Reading the before-and-after results A lower SWR is not the same as a better antenna. A choke may make SWR look worse, and still improve the system, because the coax is no longer an accidental radiator that was helping the match. Look at the whole picture: Is the SWR curve stable when you touch or move the cable? Is the noise floor lower on the bands you use? Are shack problems reduced? Do on-air reports or your own receive comparisons suggest better performance? For a clean log, record the date, weather, feed line length, choke type and position, bands tested, the SWR minimum and bandwidth, noise floor at a fixed frequency, and any shack symptoms. Photograph the setup too. When you try a different choke or a new counterpoise next month, you will have a fair comparison rather than a hazy memory. What a choke does not fix A choke is not a substitute for a good antenna, a decent radial or counterpoise system, or proper grounding. It does not provide lightning protection. Safety grounding and surge protection are separate jobs, and a choke does not replace them. It also will not cure noise produced at your own house if the source is radiating directly into the antenna. For that, you still need noise hunting: switch off breakers, test one device at a time, and use a battery-powered receiver to trace the strongest area. Bottom line If your station behaves differently when you touch the coax, start with the feed line. Take a baseline sweep, add a temporary choke, and compare SWR stability, noise, and shack behavior. It is one of the cheapest experiments in amateur radio, and the results often tell you exactly where to work next.
-
Remote station control: picking between IC-7610/RS-BA1, Flex, SCU-LAN10, RigPi and receive-only SDRs, and what to do about latency, security and rules
On security, the main rule is not to expose raw radio control to the open internet. CAT ports, serial-over-IP bridges and radio web interfaces are not designed to withstand constant scanning. A VPN such as WireGuard, or an overlay network such as Tailscale, puts the remote-control traffic inside an authenticated tunnel, so you don't have to forward the radio's ports through the router. If your ISP uses CGNAT, which prevents inbound connections, a VPN with a relay or a small cloud-hosted endpoint can sidestep the problem. Beyond that, put the radio, Pi and relays on a separate VLAN or network segment, change default credentials, keep firmware updated, and log access. Design for the case where the link dies mid-transmission. Look for a transmit timeout on the server side, a way to power-cycle or drop PTT through a separately controlled relay, and a defined state for antenna switches and amplifiers. A remote amplifier needs particular care, because a stuck key or band mismatch can do real damage. Add SWR or power protection that works without the client. For rules, there is no single answer, and you should verify with your national regulator. In the US, the Part 97 provisions on station control, control operators and telecommand are the relevant sections. They generally require that someone is acting as control operator at a control point, that the licensee remains responsible, and that the link has appropriate safeguards against loss of control. Operating a station located in another country adds another layer. The licensing and reciprocal-operation rules for the station's location and the operator's authorization both matter, and so do any contest or award rules for station location. If you share a station with others through a service, the licensee-of-record still has responsibilities for what goes out over the air.
-
Digital vs. paper QSLs: how do you split your effort between LoTW, eQSL, Club Log OQRS, bureau and direct cards?
I'll take the card design question, since it's easy to get wrong. A QSL is a record of a two-way contact, so the information has to be easy to read and unambiguous. At minimum, include: Your callsign, big and legible, plus the other station's callsign.Date and time in UTC. Say "UTC" on the card so there's no guessing.Band or frequency, and mode.Signal report (RST for CW and phone, or the report exchanged on a digital mode).A clear "2 Way QSL" or "PSE QSL / TNX QSL" indication, so the receiver knows whether you expect a card back.Your grid square, and CQ and ITU zones if you like. For some awards and for people tracking zones, those are handy.Design-wise, pick a photo or graphic that's not too busy where the callsign sits, because a gorgeous antenna photo behind tiny text is hard to read. The standard card size is about 9 x 14 cm (roughly 3.5 x 5.5 inches), which fits QSL boxes and bureau handling without trouble. Print on stock thick enough to survive sorting but light enough that it doesn't raise postage. On timelines, the honest answer is that it varies a lot. LoTW and Club Log can update within hours to days when both parties upload. Direct replies can take weeks to months, depending on the operator and the postal route. Bureau cards can take many months or longer, since they depend on batching at each end. Also, for DXCC, paper cards have to go through the approved checking process, and LoTW is simpler for most people, so it makes sense to use paper mostly for the ones that matter to you personally, or for stations that don't do LoTW.
-
Building toward EME: how band, array size, mode and polarization decisions fit together (2 m to 10 GHz)
On the 2 m and 70 cm questions, the practical entry point is mostly about how much you want to rely on larger stations. With Q65 and multi-period averaging, a modest array can work big stations that have large gain and good receivers, but it will struggle to work other small stations. If the goal is many different contacts, a larger array is the safer investment than a bigger amplifier. Doubling the power is 3 dB, and so is doubling the number of identical Yagis, but the Yagis help receive as well as transmit. Polarization is where 2 m stations lose the most signal for the least money. A fixed-polarization array will spend part of every pass in a deep fade. You can improve this with a way to rotate or switch polarization, or with separate H and V feeds and a way to select between them. If you can only afford one of those, switching is easier on the mechanics than rotating a large array. On 70 cm, the rotation is slow enough that a fixed polarization often works for long stretches. Still, the spatial offset between you and the other station can leave you off by a lot, so a polarization option remains useful. Feedline loss is often underestimated at this size. A long run of coax, plus relays and connectors, can cost more signal than a small gain increase would add. Hardline, mast-mounted relays and a preamp close to the array usually give a bigger improvement than swapping the preamp.
-
Keeper or flipper? What makes a rig worth holding onto for the long haul
I'd add that a keeper should also be easy to integrate into the rest of the station. Things like CAT control, audio interfaces for digital modes, a decent accessory jack, and how well it plays with an amplifier or an external keyer all matter more as the shack grows. A radio that's fine alone but awkward in a system tends to get sold. That's part of why a lot of people run a hybrid setup: a modern transceiver for daily work and a vintage receiver or transceiver on the side for fun. You get the convenience for contests and digital modes, and you still get the warm glow of the old gear on a quiet evening of AM or SSB ragchewing. And before buying any boat anchor, check the shipping situation. Many of these are heavy, and the packing instructions for sending them are a topic on their own. Pull the tubes, double-box the chassis, and insure it for what it's really worth.
-
Radio mods that are worth doing (and the ones that cause trouble): MARS/CAP, expanded RX, TCXO, filters, power, noise and legality
I'd put noise hunting at the top of that list, before any internal mod. Many people buy filters or hardware upgrades for a noise problem that's actually a cheap wall-wart or a bad ground. An easy test is to run the radio from a battery away from the house. If the noise vanishes, the problem is local and no filter in the rig is going to cure it. On firmware: backing up the codeplug is good advice, and I'd add that you should write down the original version number and settings before flashing. Some updates reset calibration or menu items, and you want to know what you're comparing against. For third-party firmware, read what it changes about power levels and filtering, because "unlocked" features can also loosen the radio's protections.
-
Studying for the Amateur Extra exam: which Element 4 topics are worth the most time?
I'd do both, but in a specific order: understand the building block, then drill the questions on it. The Extra pool repeats patterns a lot, so a handful of core ideas cover many questions. For the electronics sections, learn these cold. Inverting op amp gain is -Rf/Rin, and non-inverting gain is 1 + Rf/Rin. Know what a Colpitts oscillator (capacitive divider in the feedback network) looks like compared with a Hartley (tapped inductor), and why a Pierce oscillator uses a crystal. Know the difference between Class A, AB, B and C amplifier operation in terms of conduction angle, efficiency and linearity. For filters, Q = center frequency / bandwidth is used constantly, and you should recognize the tradeoffs among Butterworth (flat passband), Chebyshev (ripple, steeper skirts) and elliptical filters. For modulation, keep the FM definitions straight. Deviation is how far the carrier moves, and modulation index is deviation divided by the modulating frequency. A lot of wrong answers come from mixing those two up. On the Smith chart, you don't need to be a transmission-line expert. The center is the matched point, a normalized impedance of 1 + j0. The outer edge is pure reactance. Moving a full circle around the chart corresponds to a half wavelength of line. Those three facts cover most of the conceptual questions. For the calculation questions, work out what the answer should look like first (bigger or smaller, inductive or capacitive) and you can often eliminate two choices before touching a calculator.
-
Getting the most from 5 watts: rigs, antennas, power and where to find QRP activity
On antennas, the end-fed half-wave (EFHW) with a 49:1 transformer is popular for portable QRP because it's light, needs no radial field and can be thrown up as an inverted-L or sloper. The trade-offs are that the transformer needs good construction (core choice and winding matter for loss and heating), the pattern depends on how you hang it, and the feedline can carry common-mode current if you don't add a choke. A few turns of coax on a ferrite core near the radio can make a noticeable difference to noise and RF in the shack. If you want something simpler and more predictable, a resonant center-fed dipole or inverted V on a light mast or tree branch is hard to beat, and a linked dipole gives you several bands with just a few connectors. Whatever you pick, a few extra feet of height and keeping the wire away from metal and foliage usually helps more than changing tuners. Since QRP leaves no margin, tune the antenna with an analyzer before you set up on a summit or at a campsite.
-
From FM birds to linear transponders: handling Doppler, antennas and tracking for LEO and QO-100
On the rotator side, remember that Gpredict talks to rotators through Hamlib's rotctld, and you need to match the controller's protocol and the az/el limits before you start. Think about the cable wrap, too, and about where a pass crosses north. If the controller has a 0 to 360 range or an overlap, a pass that crosses north can make the rotator spin through nearly a full turn at the worst moment. Some controllers and programs can be configured with a flip option, or you can limit the elevation and use a conservative start azimuth. I'd also point newcomers to the difference between QO-100 and LEO work. With QO-100 the main challenges are antenna stability, dish alignment, drift and not overdriving the transponder. Keep your uplink power low, listen to the beacon level, and don't try to be the loudest signal on the narrowband transponder. The same restraint applies on the linear LEO birds: if you can hear your own downlink much louder than the beacon or other stations, reduce power.
-
Measure First: A Practical Workflow for Antenna and Station Improvements
Most station upgrades start the same way: something sounds noisy, an SWR reading looks odd, or a band feels dead, and the instinct is to put up a bigger antenna. Sometimes that's right. More often, a few simple measurements will show where the real problem is, and they give you proof when the fix works. Here is a measurement-first workflow that applies to dipoles, verticals, loops, and end-fed halfwaves alike. Start with a baseline Before touching anything, write down what the station does today. You can't claim an improvement without a "before." A useful baseline takes about twenty minutes: SWR or impedance sweep across each band you care about, taken with the same instrument each time. Noise floor on a few quiet frequencies, with the S-meter or a software reading, at set times of day. Receive comparison using a known beacon, a stable broadcast signal, or a decoded-spot tool, noting the antenna in use. A photo and sketch of the layout: feed line route, ground connections, and power supplies. Keep the notes in one place, like a notebook or spreadsheet. A simple template works: date, weather, antenna, feed line, choke used, band, SWR, noise reading, and remarks. Using a NanoVNA honestly A NanoVNA is excellent for finding resonance, checking a tuner-free match, and trimming wire lengths. A few habits keep its readings meaningful: Calibrate at the point of measurement. Use short-open-load standards at the end of the cable or adapter chain you're testing. Recalibrate when you change the frequency range. Know what you're measuring. At the end of a long, lossy coax, the cable improves the apparent SWR. A low reading at the radio end can hide a poor antenna or a high-loss line. Measuring at the feedpoint, or checking the cable's loss separately, tells you more. Keep the instrument and cables away from the antenna's near field. Common-mode current on the outside of the coax can shift readings when you touch or move the cable. Remember that SWR is not efficiency. A dummy load has a perfect SWR and radiates nothing. A low SWR only says the feedpoint is matched to the line, not that the antenna is working well. Trimming a dipole For a wire dipole, the process is mechanical. Sweep it, find where the SWR minimum or reactance zero-crossing falls, and compare it with the target. If the resonance is too low in frequency, the wire is too long; shorten both legs equally. If it's too high, add length. Make changes in small steps, because a few centimeters on each leg can move resonance by a surprising amount on the higher bands. Remember that height, nearby trees, sloping legs, and ground quality all shift the result, so measure the antenna where it will actually be used, not on the lawn. End-fed halfwave builds An EFHW depends on a high-impedance transformer, commonly 49:1 or 64:1, to match the antenna's feedpoint, which is typically in the thousands of ohms. The transformer's core, winding, and any stray capacitance all affect its behavior across bands. Because an EFHW has no balanced feedpoint, the coax shield often becomes part of the antenna, so a common-mode choke near the transformer is worth considering, or a short counterpoise wire. Test the whole assembly with the actual feed line attached. If the SWR changes when you move or touch the coax, the shield is carrying current. Baluns and common-mode chokes These two terms get mixed up, but in practice most hams need a choke: a device that adds impedance to current flowing on the outside of the coax shield. Symptoms of common-mode trouble include: RF in the shack, such as a hot microphone, a tingling chassis, or computer glitches during transmit. Noise that changes when you touch or reposition the coax. Distorted antenna patterns and SWR that varies with cable layout. A common approach is winding coax through a ferrite core, such as a type 31 mix for much of HF, or using a stack of beads. Choke performance depends on the core material, number of turns, and frequency, so check the manufacturer's data and, if possible, measure the choke's impedance with the NanoVNA. A choke that is excellent on 40 meters may do little on 10 meters. Placing one at the feedpoint and another at the shack entrance is a typical way to cover both ends. Radials and ground systems A vertical is only half an antenna, and the ground system is the other half. For a ground-mounted vertical, many shorter radials generally beat a handful of long ones, because they reduce loss in the soil near the base. For an elevated vertical, a small number of resonant radials can work well, since they're off the ground and loss is lower. Whatever the layout, check the match before and after adding radials. A falling SWR can be misleading: in poor ground setups, adding radials may raise SWR slightly while actually improving radiated signal, because loss resistance is dropping out of the system. Use a receive comparison or field-strength check alongside the VNA. Grounding versus lightning protection These are separate goals. An RF ground helps some antennas work. A safety and lightning ground protects people and equipment. Good practice includes: A single-point entrance panel where coax, rotor cables, and control lines are bonded to a ground rod system. Bonding the station ground to the building's electrical ground, following local code. Surge protectors on coax and control lines, with clear understanding that they reduce risk and do not guarantee protection from a direct strike. Disconnecting and moving coax away from the radios during storms if that's practical. For specifics, follow your local electrical code and consider hiring a qualified electrician or lightning protection professional. This is an area where guesswork is expensive and potentially dangerous. Hunting noise methodically Noise hunting rewards a systematic approach over random ferrite-clipping. Try this sequence: Run a battery-powered receiver with a simple antenna in the shack to see whether the noise is local or arrives from outside. Switch off breakers one at a time, if safe, and watch the noise level. Check the usual suspects: switching power supplies, LED lights, chargers, dimmers, solar equipment, and network gear. Walk outside with a portable AM radio or handheld receiver to follow the noise toward its source, such as a utility pole or neighbor's device. Add chokes or filters at the source only after identifying it, then re-measure. Receive antennas also matter. A small loop or a well-separated vertical can sometimes hear less local noise than a transmit antenna right above the house wiring. Close the loop with an "after" After each change, repeat the baseline measurements under similar conditions and record them next to the originals. Change one thing at a time, even if it feels slow. If you replace the feed line, add a choke, and move the antenna in one afternoon, you'll never know which change mattered. A tidy before-and-after log also makes future troubleshooting easier, because you can tell whether a new problem is a real fault or a seasonal change, like wet trees detuning a wire. The best station improvements are rarely glamorous. They're a sweep, a note, a small fix, and another sweep. Do that consistently, and your antenna projects become repeatable experiments rather than guesses.
-
Where SO2R actually adds rate: run-frequency discipline, CQ cadence and what radio 2 should be doing
One framework that helps is to treat the run as the baseline and radio 2 as an interrupt-driven job. Radio 2 only gets attention when radio 1 has nothing pending. In practice that means the CQ message sets the timing. If your CQ plus gap is about three seconds, you have a short window to tune, listen and decide. If the first thing you hear on radio 2 isn't a clear call or a known multiplier, you go back to the run right away. That fits the multiplier-hunting use case well. A quick scan of a band you aren't running on can tell you whether there's anything worth working, and you can use a bandmap or spots to prioritize. Without that, I'd expect a lot of switching with little return. A rule such as 'only call on radio 2 if the station is a new multiplier or a new band for a multiplier' also keeps the S&P side from eating the run rate. On the hardware side, the stray-signal problem is the thing that can ruin the whole approach. If radio 1 transmitting wipes out radio 2's receive, the second radio is useless in the gaps you need most. Band-pass filters, stubs, antenna separation and receive-antenna choices all matter more than the particular switching box. It's worth testing for desense with both radios on neighboring bands before the contest starts, not during it.